Tie Down Products
TranzSporter Platform Hoist
- TranzSporter TP250
- TranzSporter TP400
- Engine/Motor Options for TranzSporter
- TranzSporter Hoist Track Sections
- TranzSporter Hoist Replacement Parts
- TranzSporter Hoist Accessories
TranzSporter TP250
Previous
Next
TP250 Collapsible Carriage
250 lb. Capacity, 28 ft. Platform Hoist
Part #60040 28 ft. Hoist with Lifan Gas Engine
Part #60041 28 ft. Hoist with Honda Gas Engine
Part #60042 28 ft. Hoist with Electric Motor
Ideal for moving shingles, felt, insulation, etc. to those hard to reach locations. This hoist features a 25% increase in lifting capacity over previous models, up to 250 lbs. The new collapsible carriage comes with cam followers for better tracking and handling. Carriage also features an aluminum deck and flap for lighter weight and longer life. A rolled
goods/plywood bracket comes with unit and pins into the carriage.
TP250/TP400 Base Track Features:
• The 4 ft. heavy-duty aluminum base track utilizes laser cut steel tube support plates for job site toughness
• Amber colored carriage bumpers to protect against damage and wear from repeated lowering
• Oversized cotter pins for fast and simple removal of quick change cable drum and belt replacement
• Large cast aluminum feet for added stability
• Dual band brake system for smoother stops
Quick Access for Belt Replacement
Oversized cotter pins for fast and simple removal of quick change cable drum and belt replacement
Resources:
- WARNING: California’s Proposition 65
TranzSporter TP400
Previous
Next
TP400 Collapsible Carriage
400 lbs. Capacity, 28 ft. Platform Hoist
Part #60043 28 ft. Hoist with Lifan Gas Engine
Part #60044 28 ft. Hoist with Honda Gas Engine
Part #60045 28 ft. Hoist with Electric Motor
For heavier roofing materials, this platform hoist features a 400 lbs. lifting capacity with a lighter weight carriage and revised track system. The TP400 carriage has a 30% reduction in weight over previous model carriage. The aluminum deck and flap provide longer life and lighter weight. This carriage also features a re-engineered and simplified cam follower system with less wear parts than former hoists. Rolled goods/plywood brackets comes included and pins into carriage.
Dual Drum Brakes
Dual band brake system for smoother stops.
Plywood Brackets
Brackets are on each side. When not in use the brackets are stored flat with the collapsible carriage.
Resources:
- WARNING: California’s Proposition 65
Engine/Motor Options for TranzSporter
Previous
Next
Engine/Motor Options
The all new motor base is manufactured using laser cut steel tubing for extra strength and durability; both belt guard and foot pedal are detailed with aluminum diamond plate. Each engine mount includes a welded on steel tube with red end caps. The tube is clearly labeled and enclosed in the tube is the owners manual with detailed operating instruction.
4.0 hp Lifan Gas Engine (Standard)
• Low Oil Shut Down System – Prevents damage to engine
due to insufficient oil in engine
• Fuel Shut Off Valve – Protects engine during transportation
• Forced Splash Lubrication System
• Electronic Transistorized Ignition
• Auto Decompression – For easier pull starting
• Overhead Valve – For longer engine life
• Industrial grade components
• Fuel efficient for longer run times
• CARB and EPA certified
• Lifan comes with gear oil prefilled. Crank case oil NOT prefilled.
Part #60040 TP250/28 ft. Hoist with Lifan Gas Engine
Part #60043 TP400/28 ft. Hoist with Lifan Gas Engine
4.0 hp Honda Gas Engine
• Fuel efficient, high output operation – Overhead valve, precision
camshaft design offers precise valve timing and optimal valve overlap
• Smooth performance – Precision engineered components result in lower vibration
• Exceptionally quiet – Large capacity multi-chamber exhaust system
• Proven reliability – Low oil shutdown, cast iron cylinder sleeve, and high quality materials, fit and finish
• CARB and EPA certified
• Honda gear and crank case must be filled prior to use.
Part #60041 TP250/28 ft. Hoist with Honda Gas Engine
Part #60044 TP400/28 ft. Hoist with Honda Gas Engine
1.0 hp High Torque Electric Motor
1.0 hp, 12.8 amps, 115 Volt High Torque Leeson Electric Motor
Comes with GFCI ground-fault circuit interrupter for
safer operation.
Part #60042 TP250/28 ft. Hoist with Electric Motor
Part #60045 TP400/28 ft. Hoist with Electric Motor
Resources:
- WARNING: California’s Proposition 65
TranzSporter Hoist Accessories
Previous
Next
Solar/Plywood Panel Saddle Carriage Allows lifting of up to four solar panels or plywood sheets. Unique design allows panels to roll off towards the contractor, preventing leaning while on the roof top. Requires roof top anchoring; straps included(#13809).
Part# 48467 TP400
Part# 48469 TP250
Both TP250/400 models require a Secondary Handle Kit #48468 when used with Solar/Plywood Brackets (not included).
Secondary Handle Kit Allows use of a left side handle to engage the motor and carriage. It is required when using with the Solar/Plywood Saddle Carriage. Includes all hardware brackets and handle. Can be used for both TP250 & TP400 models.
Part# 48468
Telescopic Support Brace Used with TP250 & TP400 models over 28 ft
Part# 60005
Stand-Off/Stabilizer This unique stabilizer attaches to the platform hoist track section allowing proper stand-off from roof and gutter. Helps prevent costly gutter damage when placed directly on roof. Assembly required.
Part# 48599
Resources:
- WARNING: California’s Proposition 65
TranzSporter Hoist Track Sections
4 ft. TranzSporter Track Section
Part #10092
8 ft. TranzSporter Track Section
Part #10091
Resources:
- WARNING: California’s Proposition 65
TranzSporter Hoist Replacement Parts
(FOR MORE REPLACEMENT PARTS, SEE THE PARTS MANUAL BELOW)
Previous
Next
TP-250 Complete Carriage Wheel Kit
Kit Includes: 1/2-13 x 2-3/4” Zinc Bolts (2) 1/2” Lock Washers (2) 1/2” Washers (4) Carriage Wheels (2)
Part #90040
Brake Kit
Kit Includes: Lock Nut, Eye Bolt, Spring, Cotter Pins, Linkage & Brake Strap
Part #90007
TP-400 Complete Carriage Wheel Kit
Kit Includes: Carriage Bolts (2) Washers (2) Carriage Wheels (2) Jam Nut (2)
Part #90048
TP 250 Complete Drum Assembly
Kit Includes: Brake Drums, Cable Drum, Bearings and Cable
Part #48493A
Cable Only 100’ x 5/32”
Part #90010
TP 400 Complete Drum Assembly
Kit Includes: Brake Drums, Cable Drum, Bearings and Cable
Part #48493A-400
Cable Only 130’ x 3/16”
Part #90034
Splice Plate Kit
Kit Includes: Splice Plates (2), Bolts (8) & Keeper Nuts (8)
Part #90025
Nuts and Bolts only (16 ea.)
Part #90024
Drive Belt (51” V-Belt)
Part #10047
Resources:
- WARNING: California’s Proposition 65
Custom Manufacturing
We can make any custom product you need
State of the art CNC and robotic welding equipment ensure that our ability to create and innovate is never limited by a lack of manufacturing technology.
Wholesale Sales Contacts
Knute Chauncey
Manufactured Housing Sales Manager
404.344.0000 Ext. 1528
[email protected]